february 2015 for general signal line high ghz noise countermeasure (high-speed signal line) emc components mmz1005-v 1005[0402 inch]* * dimensions code jis[eia] chip beads mmz1005-v ty p e mmz-v series
(2/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm emc components reminders for using these products before using these products, be sure to request the delivery specifications. safety reminders please pay sufficient attention to the warnings for safe designing when using these products. the storage period is less than 12 months. be sure to follow the storage conditions (temperature: 5 to 40c, humidity: 10 to 7 5% rh or less). if the storage period elapses, the soldering of the terminal electrodes may deteriorate. do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.). before soldering, be sure to preheat components. the preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature does not exceed 150c. soldering corrections after mounting should be within the range of the conditions determined in the specifications. if overheated, a short circuit, performance deterioration, or lifespan shortening may occur. when embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions. self heating (temperature increase) occurs when the power is turned on, so the tolerance should be sufficient for the set therm al design. carefully lay out the coil for the circuit board design of the non-magnetic shield type. a malfunction may occur due to magnetic interference. use a wrist band to discharge static electricity in your body through the grounding wire. do not expose the products to magnets or magnetic fields. do not use for a purpose outside of the contents regulated in the delivery specifications. the products listed on this catalog are intended for use in general electronic equipment (av equipment, telecommunications equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement equipment, industrial robots) under a normal operation and use condition. the products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to society, person or property. if you intend to use the products in the applications listed below or if you have special requirements exceeding the range or c onditions set forth in the each catalog, please contact us. (1) aerospace/aviation equipment (2) transportation equipment (cars, electric trains, ships, etc.) (3) medical equipment (4) power-generation control equipment (5) atomic energy-related equipment (6) seabed equipment (7) transportation control equipment (8) public information-processing equipment (9) military equipment (10) electric heating apparatus, burning equipment (11) disaster prevention/crime prevention equipment (12) safety equipment (13) other applications that are not considered general-purpose applications when designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securi ng protection circuit/device or providing backup circuits in your equipment. reminders
(3/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components chip beads for general signal line high ghz noise countermeasure (high-speed signal line) features 1005 shape type noise reduction component for general signal line. features higher impedances in the ghz range compared to those of the mmz-e series chip beads. exerts an excellent noise reduction effect against noise interfering at several ghz such as lte or wi-fi, or against high-frequ ency noise. achieves particularly hi gh impedances in the range from 0.7ghz to 3ghz , enabling a reduction of noise th at could not be reduce d using the conventional mmz-e series. realizes the highest impedance in the industry at 2.5 ghz through th e adoption of a newly-developed material (according to rese arch by tdk in august 2008). application ensuring communication sens itivity of wireless communication using high-speed signals such as lte or wi-fi noise reduction for mobile equipment including smartphones and tablets or various modules noise removal for home electronics including pcs, recorders, stbs or for smartgrid s or industrial equipment part number construction operating temperature range, package quantity, product weight the storage temperature range is for after the circuit board is mounted. overview of mmz1005-v type mmz 1005 afz 750 v t 000 series name lwt dimensions material name impedance characteristic type packaging style internal code (mm) ( ) at 100mhz 1005 1.00.5x0.5 afz 750 75 v t taping 000 151 150 181 180 type temperature range package quantity individual weight operating temperature c storage temperature c (pieces/reel) mg mmz1005-v C55 to +125 C55 to +125 10,000 1 product compatible with rohs directive halogen-free compatible with lead-free solders rohs directive compliant product: see the following for more details related to rohs directive compliant products. http://produ ct.tdk.com/en/environment/rohs/ halogen-free: indicates that cl content is less than 900ppm, br content is less than 900ppm, and that the total cl and br conte nt is less than 1500ppm.
(4/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz1005-v type recommended reflow profile preheating soldering peak temp. time temp. time temp. time t1 t2 t1 t3 t2 t4 t3 150c 180c 60 to 120s 230c 30 to 60s 250 to 260c 10s natural cooling t3 t1 preheating t2 soldering t3 t3 t4 t2 t1 t: time peak t: temperature
(5/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz1005-v type shape & dimensions recommended land pattern 0.50.05 10.05 0.1min. 0.50.05 dimensions in mm dimensions in mm 0.4 0.5 0.5 0.5
(6/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz1005-v type electrical characteristics characteristics specification table measurement equipment ? equivalent measurement equipment may be used. impedance dc resistance rated current part no. [100mhz] [1ghz] [2.5ghz] ( ) tolerance ( ) tolerance ( ) ( )max. (ma)max. 75 25% 500 40% 1400 0.90 250 mmz1005afz750vt000 150 25% 1000 40% 2500 1.30 200 mmz1005afz151vt000 180 25% 1200 40% 3000 1.60 150 MMZ1005AFZ181VT000 measurement item product no. manufacturer impedance e4991a+16192a agilent technologies dc resistance type-7556 yokogawa
(7/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz1005-v type electrical characteristics z vs. frequency characteristics (by series) mmz1005-v series 10000 1000 100 101 0 frequency ( mhz ) impedance ( ) 500 1000 1500 2000 2500 3000 3500 mmz1005afz181v mmz1005afz151v mmz1005afz750v
(8/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz1005-v type electrical characteristics z, x, r vs. frequency characteristics mmz1005afz750vt000 mmz1005afz151vt000 MMZ1005AFZ181VT000 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) 0 200 400 600 800 1000 1200 1400 1600 z r x 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) 0 500 1000 1500 2000 2500 3000 z r x 1 10 100 1000 10000 frequency ( mhz ) impedance ( ) 0 500 1000 1500 2000 2500 3500 3000 z r x
(9/9) 20150203 / beads_commercial_signal_mmz1005-v_en.fm please be sure to request delivery specifications that provide further details on the features and specifications of the produc ts for proper and safe use. please note that the contents may change without any prior notice due to reasons such as upgrading. emc components mmz1005-v type packaging style reel dimensions tape dimensions dimensions in mm ty p e a b p1 k mmz1005-v 0.650.1 1.150.1 2.00.05 0.8max. ?180 2.0 2.0 0.5 ?13 0.2 ?21 0.8 dimensions in mm 1.0 ?60min. 14.4max. 8.4 +2.0 C0.0 4.00.1 2.00.05 b a p1 8.00.3 1.750.1 3.50.05 k 1.5 +0.1 0 160min. taping 200min. 300min. drawing direction dimensions in mm
|
